Home > HARDWARE > CONSTRUCTION HARDWARE > JOIST HANGERS & CONNECTORS
Choose a sub category:
JOIST HANGERS FRAMING ANGLES/ANCHORS MENDING PLATES
NAIL PLATES POST ANCHORS / CAPS FENCE BRACKETS
BRIDGING STRAPS PLYWOOD CLIPS
BRICK/WALL TIES MISC CONSTR HARDWARE
Sort By:
1 2 3 ... 5
PLATE PROTECTOR STL 1-1/2X3IN TIE HURR 18GA 6IN GALV        BRIDGING NAILLESS 2X10IN
Meets requirements of CEC rule 12-616. CSA Certified and meets the requirements of the Canadian Electrical Code. Designed to provide seismic and wind ties for trusses or joists, this versatile line may be used for general tie purposes, strongback attachments and as all-purpose ties where one member crosses another. Use (12) 8dx1-1/2 nails. Meets IAPMO UES ER-102, 112; L.A. City RR5814 and FL11478. Eliminates callbacks for nail squeaks; designed for secure grip before the drive-home blow and deeper prong penetration; precision-formed into a rigid "V" section. Meets ICC-ES-ESR-2608, 2523, L.A. City RR25725 and FL10864 codes.
TIE STRAP NO9GALV 20GA        TIE STRAP NO12GALV 20GA       STRAP TIE GALVANIZED 20GA
Straps are designed to transfer tension loads in a wide variety of applications. LSTA straps are designed for use on the edge of 2x members with a nailing diaphragm decking and wood chord open web trusses. Meets IAPMO UES ER-102, 124, ICC-ES-ESR-2105, 2523, 3096, L.A. City RR25713, 25489, 25910 and FL10852, 13872. Straps are designed to transfer tension loads in a wide variety of applications. LSTA straps are designed for use on the edge of 2x members with a nailing diaphragm decking and wood chord open web trusses. Meets IAPMO UES ER-102, 124, ICC-ES-ESR-2105, 2523, 3096, L.A. City RR25713, 25489, 25910 and FL10852, 13872. Straps are designed to transfer tension loads in a wide variety of applications. LSTA straps are designed for use on the edge of 2x members with a nailing diaphragm decking and wood chord open web trusses. Meets IAPMO UES ER-102, 124, ICC-ES-ESR-2105, 2523, 3096, L.A. City RR25713, 25489, 25910 and FL10852, 13872.
HNGR JOIST 2X8IN 18GA GALV    HANGER JST TPL SHR 18GA 2X8IN L-ANGLE  ADJUSTABLE 5IN 18GA
Distributes the load through two points on each joist nail for greater strength; it also allows the use of fewer nails, faster installation and the use of standard nails for all connections. Do not bend or remove tabs. Use hot-dip galvanized (HDG) nails with ZMAX and HDG connector products; 16d sinkers may be used where 10d commons are specified with no reduction in load; with 3x carrying members, use 16dx2-1/2" nails into the header and 16d commons into the joist with no load reduction; with 2x carrying members, use 10dx1-1/2" nails into the header and 10d commons into the joist, reduce the load to 0.64 of the tabel value. Meets ICC-ES-ESR-2549, 2523, 3096, L.A. City RR25807, 25910 and FL10655. Distributes the load through two points on each joist nail for greater strength; it also allows the use of fewer nails, faster installation and the use of standard nails for all connections. Do not bend or remove tabs. Use hot-dip galvanized (HDG) nails with ZMAX and HDG connector products; 16d sinkers may be used where 10d commons are specified with no reduction in load; with 3x carrying members, use 16dx2-1/2" nails into the header and 16d commons into the joist with no load reduction; with 2x carrying members, use 10dx1-1/2" nails into the header and 10d commons into the joist, reduce the load to 0.64 of the tabel value. Meets ICC-ES-ESR-2549, 2523, 3096, L.A. City RR25807, 25910 and FL10655. Used to reinforce 90? connections; staggered fastener pattern reduces the chances of wood splitting; stronger than angled nailing or screw fastening; cut-outs along the bend line make bending easier (may be bent from 0 to 135?); "ZMAX" galvanization offers extra corrosion resistance for exterior and treated-wood applications; install with 10d common nails or #9 x 1-1/2" "Strong-Drive" SD screws.
BRACKET SADDLE DECO 4IN BLACK TIE STRINGER ADJUSTABLE 18GA  HNGR ADJ GALV 2X6IN 18GA
Connects wooden posts to concrete footings for deck supports. Suitable for installation on 2" x 10" or 2 x 12" header/rim joist; may be installed flush with the top of the carrying member or lower on the face; interchangeable for left or right applications; "ZMAX" galvanization offers extra corrosion resistance for exterior and treated-wood applications; install with (17) 10d x 1-1/2" nails or #9 x 1-1/2" "Strong-Drive" SD screws. This product is preferable to similar connectors because of easier installation, higher loads and lower installed cost; attach the sloped joist at both ends so that the horizontal force developed by the slope is fully supported by the supporting members; adjustments can be made in the field; "ZMAX" galvanization offers extra corrosion resistance for exterior and treated wood applications; install with 10d common and 10d x 1-1/2" nails.
CLP SHEATHING 1/2IN STL       BRACKET SADDLE DECO 6IN BLACK 6650 1-1/2IN X 3IN PLATE WOOD
Quick installation, no nails required; keeps panels even for a level structural plane; provides the 1/8" space between plywood panels as recommended by the American Plywood Association; use the same size sheathing clip as the panel thickness; galvanized for extra corrosion resistance. Connects wooden posts to concrete footings for deck supports. Protector plate. Meets requirement of CEC rule 12-616.?
CLP SHEATHING 7/16IN STL      OZHH320GRN  3.58INX32.89IN GRO STRIP DCK FRAME WTRPF 3INX72FT
Quick installation, no nails required; keeps panels even for a level structural plane; provides the 1/8" space between plywood panels as recommended by the American Plywood Association; use the same size sheathing clip as the panel thickness; galvanized for extra corrosion resistance. Green Ground Spike. 4" X 32". Made from standard tarred roof paper, this impermable band prevents wood decay; larger than the simple joist, it diverts water to each side; offers maximum protection for your deck; just unroll it on the frame structure and staple it.
BS PST 4X4IN 12GA GALV        SADDLE 4X4IN GALV CARPORT     HNGR JOIST 16GA 2X10IN
Provides a connection between a post (or column) for decks, patio covers and other top-supported structures. Uses (12) 16d nails for installation. Allowable loads: 1485 lbs. non-cracked and 1040 lbs. cracked. Meets ICC-ES-ESR-3050, L.A. city RR25985 and FL10849 codes. Use for connecting post to concrete; hot dipped galvanized; use (4) 16d fasteners for installation. Can accommodate joists skewed 40 to 50 degrees; angled nail slots direct nails for proper installation; "ZMAX" galvanization offers extra corrosion resistance for exterior and treated-wood applications; install with 16d common nails in the header and 10d x 1-1/2" nails in the joist.
CLP PLYWD 20GA 7/16IN 250/BG  STRIP FRM WTHRPRF 4-1/2INX72FT HNGR JOIST 16GA 2X10IN
Quick installation, no nails required; keeps panels even for a level structural plane; provides the 1/8" space between plywood panels as recommended by the American Plywood Association; use the same size sheathing clip as the panel thickness; galvanized for extra corrosion resistance. Can accommodate joists skewed 40 to 50 degrees; angled nail slots direct nails for proper installation; "ZMAX" galvanization offers extra corrosion resistance for exterior and treated-wood applications; install with 16d common nails in the header and 10d x 1-1/2" nails in the joist.
DECKBRACKET GALVANIZED STRATTO BASE COLUMN GALVANIZED 12GA   CLP PLYWD 20GA 3/8IN 250/BG
"Stratton Bracket". Galvanized steel. Help connect posts to the concrete for a broad range or members. Install with 12-16d nails and (2) 1/2" machine bolts. Quick installation, no nails required; keeps panels even for a level structural plane; provides the 1/8" space between plywood panels as recommended by the American Plywood Association; use the same size sheathing clip as the panel thickness; galvanized for extra corrosion resistance.
CLP PLYWD 20GA 1/2IN 250/BG   CLP PLYWD 20GA 5/8IN 250/BG   DECK BENCH BRKT 2X4IN SAND
Quick installation, no nails required; keeps panels even for a level structural plane; provides the 1/8" space between plywood panels as recommended by the American Plywood Association; use the same size sheathing clip as the panel thickness; galvanized for extra corrosion resistance. Quick installation, no nails required; keeps panels even for a level structural plane; provides the 1/8" space between plywood panels as recommended by the American Plywood Association; use the same size sheathing clip as the panel thickness; galvanized for extra corrosion resistance. You determine the size. Connect with railing brackets with 2x4 and 2x6 lumber to easily add a bench to any size or shape deck. Gain increased seating area while using only 7" of deck space. Assembled unit stands 36"H for deck railing, seat is 17"H. Quick and easy to assemble using basic tools. Includes bench bracket, hardware and instructions. LUMBER NOT INCLUDED.
   
 
1 2 3 ... 5